Exactly How to Install a Bath Tub Yourself: Removing as well as Replacing.
Exactly How to Install a Bath Tub Yourself: Removing as well as Replacing.
Blog Article
How do you feel on the subject of How to Install a Bathtub?
Mounting a bath tub isn't specifically brain surgery, yet it does call for strong plumbing, woodworking, and also often, tiling skills. Replacing an old tub with a new one is also a moderately difficult project. If the old tub is readily accessible, the task can relocate easily; if you need to open up a wall surface to eliminate the old tub and position the brand-new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's skills, although you will certainly require an assistant to vacate the old bathtub as well as set in the new one. See to it you have qualified yourself for the job and are comfortable attempting it. Rather than working with a specialist to take control of a halfway-completed job, it is much better to think about employing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This article will aid you mount a brand-new tub in your restroom if you have already acquired a brand-new bathtub as well as don't need to transform the setup of your previous water system pipes.
Your devices and also material checklist need to consist of the following:
Getting ready for the Installation
To start with, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to make certain that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps system to avoid strain on the bath tub.
Fit the versatile tap connectors to the bottom of both faucets using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water system. After doing so, turn on the taps to drain pipes any water remaining in the system. The process of getting rid of the existing taps can be rather bothersome due to the restricted accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will come from the pipelines. As soon as the supply pipelines have actually been removed, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old securing substance.
Prior to going on to fit the new taps, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Utilizing the two wood boards under its feet, position the bath tub in the called for placement. The wood boards are handy in equally spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little points.
The following goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the tub until the spirit level reads level.
To install taps, fit the bottom of the furthest flexible tap port to the suitable supply pipe by making a compression join; after that do the very same for the various other faucet.
Activate the water and also inspect all joints as well as brand-new pipework for leakages as well as tighten them if necessary. Fill the bathtub as well as additionally examine the overflow electrical outlet as well as the typical electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling as well as sealing around the bathtub needs to wait until the bathtub has actually been made use of a minimum of once as this will resolve it right into its last setting.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will require a plastic port to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the mounting opening in the bath/basin guaranteeing that the washers are in area in between the tap and the sink. Safeguard the faucet in position with the maker provided backnut. As soon as the faucet is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical tap adapters. The former kind must be connected to the faucet ends first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to crack an inflexible seal, causing the water to penetrate the wall surface in between the bath and also the tiling, causing complications with moisture and also possible leakages to the ceiling below.
You can choose from a range of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes as well as cartridges, and also are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill up the bathtub with water before sealing, to enable the activity experienced when the tub remains in usage. The sealant can split rather early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently available on the market. It is a good idea to fit the floor tiles making use of water-resistant or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I have been very occupied with How to Install a Bathtub Yourself and I really hope you appreciated the new entry. If you liked our article plz do not forget to share it. Thank you for your time. Come back soon.
Book Your Service Report this page